95mitsugsx
05-06-2008, 07:43 PM
Welcome to my ’08 build thread.
I currently have two ’95 GSX’s. One is a white GSX and it was my first DSM. The other is a red GSX. I did minor mods. to the white GSX the first year until my engine and I decided to go take a WALK together. I then did some research and found that putting the 6-bolt in it was the best route to go. I did some more research and found a fellow DSMer in Minnesota that had built some motors, so I decided to go with him for the 6-bolt build. The reason for not doing the work my self was lack of garage, and time (Full time student/ full time Pizza Hut delivery driver). After myself, and another dsmtalk member decided to go with EclipseRST (vogelperformance.com) he decided to spend our money elsewhere. Long story short I am out $3,600 until court time.
One year later, I started saving money again and bought a locally built short block with Wiseco 8.5:1 forged pistons, Eagle H-Beam rods, Mitsubishi uncut crank, ARP head studs, and removed balanced shafts. While looking at the short block at the seller’s house I asked to see his GSX for sale. It had just recently had a 12 point roll cage installed. The exterior was immaculate, as well as the exterior. He was selling it for $1000, so I figured it was to good of a buy to pass up.
Now at the present time I have my white GSX at my friend Keith’s( Plum ’97 GST) house ready for disassembly. I owe a couple more hundred dollars on the red GSX and should be picking it up May 12th.
Here are some pictures of the cars and parts purchased so far for the ’08 build.
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/WhiteGSX.jpg
This is the ’95 White GSX
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Headliner.jpg
Unusable suede headliner (Red GSX has sunroof)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Suede_Door_Panel.jpg
Suede door inserts(Going in red GSX)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/CorbeauSeats.jpg
Suede Corbeau Seats and suede rear window panels (going in red car)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Clean_UP.jpg
Kieth donated usage of garage during build.
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Keiths_DSM.jpg
Keith’s ’97 GST(just purchased a week ago)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/GST_vs_GSX.jpg
GST vs GSX
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/CleanStart_2.jpg
Cleaned up garage
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/6_Bolt.jpg
New 6-bolt
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Evo316G.jpg
Evo 3 16G (break in turbo)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Evo316G_Front.jpg
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Evo316G_Port.jpg
Ported side(welded internal gate)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Exhaustmani_WG.jpg
Exhaust manifold w/ HKS W.G.
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Exhaustmani.jpg
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Exhaustmani_WG_2.jpg
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Rear_CAGE.jpg
Rear cage
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Side_RollCAGE.jpg
Going to paint cage exterior color to match, but whole front half will have black silicone padding.
That's all I have know, but come May 12th the build will be ready to go so wish me good luck!
I currently have two ’95 GSX’s. One is a white GSX and it was my first DSM. The other is a red GSX. I did minor mods. to the white GSX the first year until my engine and I decided to go take a WALK together. I then did some research and found that putting the 6-bolt in it was the best route to go. I did some more research and found a fellow DSMer in Minnesota that had built some motors, so I decided to go with him for the 6-bolt build. The reason for not doing the work my self was lack of garage, and time (Full time student/ full time Pizza Hut delivery driver). After myself, and another dsmtalk member decided to go with EclipseRST (vogelperformance.com) he decided to spend our money elsewhere. Long story short I am out $3,600 until court time.
One year later, I started saving money again and bought a locally built short block with Wiseco 8.5:1 forged pistons, Eagle H-Beam rods, Mitsubishi uncut crank, ARP head studs, and removed balanced shafts. While looking at the short block at the seller’s house I asked to see his GSX for sale. It had just recently had a 12 point roll cage installed. The exterior was immaculate, as well as the exterior. He was selling it for $1000, so I figured it was to good of a buy to pass up.
Now at the present time I have my white GSX at my friend Keith’s( Plum ’97 GST) house ready for disassembly. I owe a couple more hundred dollars on the red GSX and should be picking it up May 12th.
Here are some pictures of the cars and parts purchased so far for the ’08 build.
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/WhiteGSX.jpg
This is the ’95 White GSX
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Headliner.jpg
Unusable suede headliner (Red GSX has sunroof)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Suede_Door_Panel.jpg
Suede door inserts(Going in red GSX)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/CorbeauSeats.jpg
Suede Corbeau Seats and suede rear window panels (going in red car)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Clean_UP.jpg
Kieth donated usage of garage during build.
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Keiths_DSM.jpg
Keith’s ’97 GST(just purchased a week ago)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/GST_vs_GSX.jpg
GST vs GSX
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/CleanStart_2.jpg
Cleaned up garage
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/6_Bolt.jpg
New 6-bolt
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Evo316G.jpg
Evo 3 16G (break in turbo)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Evo316G_Front.jpg
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Evo316G_Port.jpg
Ported side(welded internal gate)
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Exhaustmani_WG.jpg
Exhaust manifold w/ HKS W.G.
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Exhaustmani.jpg
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Exhaustmani_WG_2.jpg
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Rear_CAGE.jpg
Rear cage
http://i89.photobucket.com/albums/k210/jts241/95mitsugsx%2008Build/Side_RollCAGE.jpg
Going to paint cage exterior color to match, but whole front half will have black silicone padding.
That's all I have know, but come May 12th the build will be ready to go so wish me good luck!