DSMTalk Forums: Mitsubishi Eclipse, Plymouth Laser, and Eagle Talon Forum banner

Wheel/Tire fitment Thread

14K views 14 replies 11 participants last post by  LatDSM 
#1 · (Edited)
Follow this please:
1.Brand of Rim-
2.Rim size (diameter and width)-
3.Offset-
4.Brand of tire-
5.Tire size-
6.Suspension-
7.Do they rub-
8. What Brakes-
9. Camber?
10. Fender work? (Roll? Cut? Pull?)
 
#2 ·
1.Brand of Rim- GM C4 Sawblade
2.Rim size (diameter and width)- 17x9.5
3.Offset- +56 with 25mm adaptor effective 31mm
4.Brand of tire- NA
5.Tire size- NA
6.Suspension- Ksport coilovers
7.Do they rub- NA
8. What Brakes- stock 1g rear



Just a start. Lets get this thing going!
 
#3 · (Edited)
Is this for the herrafrush types only? If not, here goes my maxed out non rolled, non aggressive type setup:

1. Rays G-games 77wolf (discontinued)
2. 18x7.5"
3. +42
4. Sumitomo
5. P225-40-18
6. Eibach Prokit KONI Yellows
7. nope
8. stock

 
#7 ·
Ok.
 
#6 ·
1.Brand of Rim- Advan RG-1
2.Rim size (diameter and width)- 18x.9.5
3.Offset- +35
4.Brand of tire- General Exclaim
5.Tire size- 255/35
6.Suspension- Tein SS Coilovers
7.Do they rub- Rears do (keep in mind I have an adjusting collar taken out on the rear coilovers, so I am pretty dang low in the rear. And I run a meaty tire
8. What Brakes- Evo brakes front and rear
9. Camber - Front is -1.8, rear is -2.8
10. Rolling? - Front and rear are rolled somewhat. Rear lip was just folded over itself, not cut. No pulling at all





I added number 9 and 10 because I think they are necessary for determining fitment. As Wade knows, the car is down for a bit for upgrades, so I will get fitment pictures once it is on the ground again
 
#8 ·
1.Brand of Rim- CCW Classics
2.Rim size (diameter and width)- 16 x 8
3.Offset +32
4.Brand of tire- Hoosier
5.Tire size- 26-9.5/16
6.Suspension- Ksport coilovers
7.Do they rub-With the height adjusted correctly they do not rub.
8. What Brakes- 2g front 1g rear
9. Camber -never checked
10. Rolling? - none

 
#10 · (Edited)
1.Brand of Rim- Enkei EKM3
2.Rim size (diameter and width)- 18x8
3.Offset- +40
4.Brand of tire- Pirelli
5.Tire size- 235/40
6.Suspension- Tokico Blue shocks and Tokico HP springs (1.75" drop).
7.Do they rub- Rears rubbed the pinch weld during hard corners/bumps. Front inner sidewalls rub during hard corners, which I have yet to look into farther.
8. What Brakes- Early '95 stock brakes.
9. Camber? No exact specs yet. Currently using 3 washers behind the rear UCA's to help compensate for lowering.
10. Fender work? (Roll? Cut? Pull?) The rear pinch welds have been folded back, but no cutting or pulling.



 
#13 ·
Follow this please:
1.Brand of Rim- 5Zigen FN01R-C Hot Versiom
2.Rim size 17x8
3.Offset-+35
4.Brand of tire- Sumitomo HTR-Z
5.Tire size- 245/40ZR17
6.Suspension- Megan Racing Coilovers
7.Do they rub- No
8. What Brakes- Dual Piston "Big Brakes" standard rear
9. Camber? -3* front
10. Fender work? (Roll? Cut? Pull?) none





 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top