DSMTalk Forums: Mitsubishi Eclipse, Plymouth Laser, and Eagle Talon Forum banner

Status
Not open for further replies.
1 - 20 of 108 Posts

·
Elite DSMtalker
Joined
·
1,386 Posts
Discussion Starter #1
im parting out my 90 tsi awd as i'm in need of some cash right now plus i'm starting on a 94 tsi project. car was in a front end collision if you want any parts off the car just reply or pm, prefferable reply. i have pics of everything i can take pics of and i have pics if needed to prove whats in the block. they're too big to post on here unfortunately. i'm leaving it up to you guys to make offers on all the parts.

Mods: all have under 10 000kms on them
- aermotive pressure regulator (stainless lines)
- 255 fuel pump
- 1g datalogger
- rebuilt and ported head with the 272/264 hks combo
- freshly rebuilt 6 bolt block with 9:1 comp ross pistons, all new bearings and seals, whole new timing assembly (belt, bearings, pulleys, tensioner)
- unported and unclipped evo3 16g
- prothane motor mounts all around
- 3" turboback made by myself
- sbr race fmic flanged for greddy type s
- mild steel j pipe
- maf-t and gm mas
- hacked 1g mas
- universal 3" air filter
- short shifter from ralliart (never installed)
- front strut tower bar
- aluminum catch can
- magnus built transmission (double syncs and all the goodies)
- act2100
- fidanza flywheel
- greddy type s bov
- 17" rims with kumho tires (2 712s and 2 711s)
- 2 22 spline transfer cases
 

·
Registered
Joined
·
206 Posts
1g datalogger
freshly rebuilt 6 bolt block with 9:1 comp ross pistons, all new bearings and seals, whole new timing assembly (belt, bearings, pulleys, tensioner)
3" turboback made by myself
act2100
maf-t and gm mas
how much for these parts?
 

·
Honorary Moderator
Joined
·
1,361 Posts
PM me prices and pics for:

-AFPR
-Prothane motor mounts
-EVO3 16G

Thanks,

Mike
 

·
Registered
Joined
·
31 Posts
How much for:
- act2100
- fidanza flywheel
 

·
Registered
Joined
·
346 Posts
how much for the turboback exhaust... and what kind of bends is it? Emal me some pics at [email protected]
 

·
Registered
Joined
·
346 Posts
ooo and catch can
 

·
Registered
Joined
·
346 Posts
cant you just cut the exhaust up to 3-4 parts, and box it? i can weld the parts together its no biggie..... and why 50 bucks for the catch can
 

·
Elite DSMtalker
Joined
·
1,386 Posts
Discussion Starter #16
because there's like 40 bucks worth of aluminum and fittings and then all the argon i used to weld it up. and if you want me to cut it all up so u can weld it again why don't u just buy the bends and build your own? :confused: and unfortunately i have no self control and i would cut it into 100 tiny peices just to laught thinking about you opening the box. but seriously i don't really want to sell the exhaust unless its locally.
 

·
Elite DSMtalker
Joined
·
1,386 Posts
Discussion Starter #18
everything is still up fro grabs i'll post whenever something gets sold to keep everyone updated.
 

·
Registered
Joined
·
292 Posts
how much for the maft stuff and the 16g?
 
1 - 20 of 108 Posts
Status
Not open for further replies.
Top